Advken Dark Mesh Sub Ohm Tank Review

These days we are going to possess a basic hero from Advken. Recently, they decently sat upon low-support – two of the 3 severe products belonged to this particular specific detachment. To be truthful, it’s rather strange to observe this kind of image, because these folks can decently make serviced atomizers. And the most interesting factor is the fact that, usually, non-servants are added to boxing mods, but this is simply not a story about Advken – they only stamp tanks. Perhaps this situation will likely be a different, as well as a tiny later we are going to nevertheless come to be witnesses from the update of the lineup of boxing mods – we check with!

Advken Dark Mesh Sub Ohm Tank 
Advken Dark Mesh Sub Ohm Tank - again not a service ...
Case Material: Stainless Steel Atomizer
Type: Maintenance- Free
Evaporators: 0.15Ω
Capacity: 5 / 6ml
Diameter:28mm
Height: 54.5mm with drip type
Connector: 510, pin gilded
Weight: unknown
Color: see photo below
Advken Dark Mesh Sub Ohm Tank - again not a service ...
Options
– Dark Mesh Sub Ohm Tank
– replaceable evaporators 2pcs 0.15Ω (one pre-installed)
– spare origins
– traditional rag
– spare glass
– certificate

The exterior of our visitor is fairly regular for that segment to which he belongs. This is a reasonably enormous example, however, in size, it is not the greatest. Specific dangers and of course the colorful drip sort are responsible for the decoration.

Advken Dark Mesh Sub Ohm Tank - again not a service ...

Release colors were only two, and those are timeless. It is most likely that later the designers will be ample with additional colors.

Advken Dark Mesh Sub Ohm Tank - again not a service ...

The drip kind is made of resin, getting 810th. He is located inside the lid, the locking mechanism of which may well be threaded. This imagined encouraged me for the large number of dangers around the latter. The filling up slots had been not proven to us, I do believe they will be of good dimensions.

Advken Dark Mesh Sub Ohm Tank - again not a service ...

Two kinds of replaceable evaporators are available, both of them over a grid. In the initial situation, one particular performance, inside the other triple.

Advken Dark Mesh Sub Ohm Tank - again not a service ...

The capability is decent from the beginning, also it can differ depending on the kind of evaporator employed.A spare window is another bubble of rendering.

Advken Dark Mesh Sub Ohm Tank - again not a service ...

A massive rotary engagement ring with dangers is mainly responsible for adjusting the airflow. Naturally, to blow this kind of serious evaporators you will need reasonable air intake openings, therefore the designers chose to make such as many as four.

Advken Dark Mesh Sub Ohm Tank - again not a service ...

Click Here Ave40  For Vape Wholesale Cooperation.

Now It’s Available: Advken Dark Mesh Sub Ohm Tank
Hot Sale Recommendation:

Vaporesso Aurora Play Zippo Pod Starter Kit

Dovpo Topside Dual Squonk Box Mod

Lost Vape Drone BF DNA250C Squonk Box Mod

Voopoo Drag Nano Kit

OUMIER Armadillo RDA

Vape Wholesale & buy Electronic Cigarettes online in Bulk. 2m*1i9y0a7j*

Quality Vape Products, Trusted Vape Wholesale Supply by VapeShops Owners.

WHOLESALE INQUIRY: https://www.ave40.com/wholesale-service.html

Starter-Kits:https://www.ave40.com/starter-kits/disposable-pod-system-kits

Why The Toilet Seat Size Matters?

Are you thinking to replace your old toilet seat and not able to decide the seat size you want for the bathroom don’t worry, here is the solution of your problem. The toilet seat must be comfortable to sit upon, the day starts from going to the bathroom first. so the bathroom should be well managed with all the comforts. When it comes to toilet seat one should take it sincerely, it affects our body posture and digestive system if you do not flush properly. The toilet seat sizes are something to take care of choosing the right seat for you as per your weight and height. The selection of toilet seat is done on the basis of size, material, and style.

Standard toilet seat sizes:

The standard toilet seat size varies from 21 inches to 31 inches with 14-16 inches distance from the wall to closet bolts. The depth of the seat varies from 27-30 inches.

Types of toilet seats:

Toilet seats are generally of four types: Round bowl, Elongated bowl, Square bowl, Rectangle bowl in spite of these Some Of the types of toilet seats described below:

1.Gravity-feed toilet: The toilet gets flush with gravity. The gravity-feed toilet utilizing siphoning action in the bowl to flush the waste.

Square Slow Close Toilet Seat
Square Slow Close Toilet Seat

2.Smart Toilet: The smart toilet is the latest in the market, its electronic cover senses human entrance and lift up automatically. It plays lyrics when someone approaches near. The temperature of the seat can be adjusted and the release of water pressure can be managed with dual flush functionality.

3.Tornado toilet: The new model water closet with round seat cover flushes and clean properly at the same time. With the inbuilt feature of cleaning it gets clean automatically after flush.

4. Waterless toilet: The waterless toilet is not common in the house but used for camping purposes, working sites, and during a home renovation. It does not use water and the waste is collected at under beneath. This is for the situation when the water is not available.

Buying the toilet seat:

When you go to buy a toilet seat takes care of the comfort it presents and the quality. Today the new technology-based toilet seats are replacing the old fashioned toilet seats. So buy the best toilet seat having adjustable quality and new features that makes your bathroom time happy and comfortable. There are many brands offering great deals on the toilet seats online which will not cost you high.

How Toilet seat sizes affect?

Shell Resin Toilet Seat
Shell Resin Toilet Seat

For every person the toilet seat sizes matters, if the seat is of the perfect size it feels more comfortable. Before buying the toilet seat check out the perfect toilet seat sizes take the measurements of the distance from the wall to the closet bolts or you can take help from the expert for choosing the right toilet seat for you.

Conclusion: It is very confusing to decide the apt choice when you have thousands of choices, choose the perfect match for your bathroom after exploring different toilet seat sizes, prices, and features.

How to Install a Slow Close Toilet Seat | Knowledge Base – HomeRises
https://www.homerises.com/…/to-teach-you-how-to-install-the-slow-close-toilet-seat/
Jun 4, 2019 – But it may be more difficult for one to get the installation of the toilet seat. So let’s start with the toilet seat slow closing problem and teach you …
Toilet Seats – American Standard
https://www.americanstandard-us.com/
There are industry standards for toilet seats – all toilets have seat post holes on 5 1/2″ centers – all elongated bowls are 18 1/2″ from seat posts to front of rim, …

Vaporesso Target Mini 2 kit -a new stealth device

Well, and finally, I invite you to meet a new member of the Target family from Vaporesso. Stealth devices always attract attention, and on the eve of the coming hot season for many, or rather for the majority, this issue becomes very relevant.

Vaporesso Target Mini 2 kit 
Vaporesso Target Mini 2 kit - a brand new stealth device for the coming summer ...
Dimensions: 58.1 x 37.2 x 25.7mm (only mod)
Weight: unknown
Case material: plastic + metal
Power supply: built-in 2000 mAh
Chipset: Omni 4.2
Output power: 5 – 50W
Operating mode: POWER
Supported resistance: 0.03 – 5.0 Ω
Protection:low / high resistance, overheating, short circuit, incorrect polarity, overcharging / overdispluing
Connector type: steel 510, pin gold-plated, spring-loaded
Screen / diagonal: yes, 0.66 ”
Micro-USB port / charging: yes, charging current 2A
Color: see photo below
Vaporesso Target Mini 2 kit - a brand new stealth device for the coming summer ...
VM TANK 22mm 

Case material: stainless steel
Atomizer type: maintenance-free
Evaporators: 0.6 / 1.0Ω
Capacity: 2 ml
Diameter: 22mm
Height: 49mm with Drip type
Connector: 510, pin gold-plated
Weight: unknown
Color:steel and dark

Focus On www.urvapin.com For More Vape Start Kit.

Completion
– Target Mini 2 mod
– VM TANK 22mm
– replaceable evaporators 2pcs 0.6 / 1.0Ω (one preinstalled)
– spare glass
– spare origings
– key
– USB cable
– user manual
– warranty card
Vaporesso Target Mini 2 kit - a brand new stealth device for the coming summer ...
The design of our hero is not very different from all representatives family – mod still repeats the outlines of the pistol grip with the corresponding anatomical grooves. Therefore, as before, ergonomics promises to be decent.
Vaporesso Target Mini 2 kit - a brand new stealth device for the coming summer ...
Dimensions of our guest is somewhat different from the forefather. As I understand it, he is still bigger.
Vaporesso Target Mini 2 kit - a brand new stealth device for the coming summer ...
The complete non-service is new, and it is presented in three versions at once, however, the version with a diameter of 22 mm was included in the set.
Vaporesso Target Mini 2 kit - a brand new stealth device for the coming summer ...
It will refuel from above, the capacity is very small.
Vaporesso Target Mini 2 kit - a brand new stealth device for the coming summer ...
Two types are offered as replaceable evaporators. Moreover, their change is possible even with a full tank.
Blowing adjustment is present, it is point.
Vaporesso Target Mini 2 kit - a brand new stealth device for the coming summer ...
Vaporesso Target Mini 2 kit - a brand new stealth device for the coming summer ...
The stock on the landing of the boxing mod is not known for certain, it is likely that atoms more than 22 mm in diameter will not be able to be taken on board.

Focus On www.urvapin.com For More Best Vape mods.

Vaporesso Target Mini 2 kit - a brand new stealth device for the coming summer ...
The control panel boxing mod has changed not so much. The fire button is still reminiscent of a gun trigger. A small monochrome display settled slightly lower. And at the very bottom, there are three control keys.
Vaporesso Target Mini 2 kit - a brand new stealth device for the coming summer ...
Here again, the built-in battery, that’s just its capacity has grown after the size. Connector for charging settled on the sidewall and charging will be fast – only about an hour.
Vaporesso Target Mini 2 kit - a brand new stealth device for the coming summer ...
The price of $ 62.99.

Vaporesso Target Mini 2 kit - a brand new stealth device for the coming summer ...

Focus On www.urvapin.com to See More New Devices.

Now It’s Available: Vaporesso Target Mini 2 II 50W Battery Kit 2000mAh

Hot Sale Recommendation:

Vaporesso Aurora Play Zippo Pod Starter Kit

Rincoe Mechman Mesh Kit

Voopoo Drag Nano Kit

Voopoo Drag Baby Kit

Justfog Compact 14 Starter Kit

Rincoe Mechman Kit Review

Rincoe is no strangers to vaping. Thanks to the unique styling of their Manto S and Manto Mini-mods, they have been quite popular among vapers. Who doesn’t like a cool looking mod? The newest addition to their lineup is the Mechman 228W kit and it’s just as enticing and customizable as the rest.

The outside of the Mechman comes in three different stylings and there are three different choices of panel designs. But you can also remove the panels and replace the sticker with a custom-printed panel of your choice for added personal flare.

So it looks cool — but how does it perform? In this review, I’m going to go over everything you need to know about the Rincoe Mechman kit and you can decide for yourself if it’s worth picking up.

1 x Mechman 228W Mod
1 x Mechman Mesh Tank
1 x 0.25ohm Single Mesh Coil (Pre-Installed)
1 x 0.20ohm Dual Mesh Coil
1 x Extra Bubble Glass
1 x Charging Cable
1 x User Manual
1 x Spare Parts

Specifications

Size: 53.8mm x 29.2mm x 90mm
Power Range: 1-228W
Temperature Control Mode: Ni200/Ti/SS
Power Mode, Bypass Mode, TCR
Uses Two 18650 Batteries
Interchangeable Stickers & Panels

Focus On www.urvapin.com to See More New Devices.

Overview


The Mechman gets it name from it’s all-metal, mechanical looking design. As a whole, it’s a pretty good looking kit. It’s not too heavy though, even with the batteries installed. You can get the mod in either black or silver with three different chassis styles: Steel Case, Steel Wings or Steel Bones. You can also get each style in four different panel designs: camouflage, American flag, Union flag or a mean looking wolf.

The mod is powered by dual 18650 batteries and fires at up to 228W in power mode. It has power mode, bypass mode, temperature control mode and TCR. As far as a menu goes, it doesn’t have one but this keeps the mod simple and easy to use.

The kit comes with the Mechman sub-ohm tank. It’s a 28mm tank made of stainless steel that uses a wide 810 resin drip tip. It comes with a 4.5ml capacity bubble glass and includes two different mesh coils. You get a 0.20ohm and a 0.25ohm coil with the kit.

My first impressions of the Mechman kit are pretty good. It looks good and feels good to hold. The 228W output is higher than most mods I’ve got a chance to review. Plus, it comes with some decent-looking mesh coils. We’ll see how it holds up.

Design & Build Quality


The Mechman is a nice size for a dual battery mod. It’s not too tall and not too wide. It’s got rounded edges that make it comfortable to hold and it fit in my hand very comfortably. The body of the device is also made entirely of metal so it’s pretty durable. I got the black “Steel Wings” style of the mod for this review and the mechanical design is pretty cool — it looks very modern and clean. I got a number of compliments while using the mod from other fellow vapers and they all wanted to know where they could get one. That’s a really good sign in terms of design.

The American flag front panel is also very neat. If you’re from the U.S and looking to show your patriotism with a vape mod then this is definitely the one to do it with. But what’s neat about this mod is that you’re able to remove the “Steel Wings” that cover the front panel (provided you have access to a small torx screwdriver) and put a sticker of your choice underneath. I haven’t gotten around to printing off a “Versed Vaper” panel but it’s definitely on my to-do list. I haven’t seen another mod that allows you to do something like this so it’s definitely unique.

The back panel of the Mechman is a removable battery door. It’s magnetically attached and pulls off just like most other dual battery mods. This panel is similar in design to the front, with the Steel Wings, however you can’t remove the screws to insert a custom design. It’s got a grid-style pattern that matches the rest of the mod though so I have no complaints.

The 510 is centered and in my books that’s always a good thing; it makes the mod look much nicer with a tank installed. There are three buttons: a rocker-style firing button and two smaller adjustment buttons. The fire button takes the perfect amount of pressure to press and isn’t too light. The adjustment buttons are also the same pressure-wise and feel just as firm and well-built.

The screen is large on the Mechman mod and the readouts are clear. It’s a black and white screen, not color, but that isn’t too big of a deal. There’s no way to adjust the brightness, but even outdoors I found it bright enough to see. Just under the screen and the buttons is a micro-USB port for firmware updates and charging. If you’re in a pickle this device does support pass-thru charging and that’s a pro.

Click Here Ave40 For Vape Wholesale Cooperation.

Mechman Mesh Sub-Ohm Tank


The Mechman tank is 28mm in diameter. It matches the mod and uses a bubble glass that gives it a 4.5ml max capacity. In case you break the glass, the kit includes a spare identical glass which I rate. It’s got a wide 810 drip tip made of resin that is pretty nice but it’s also interchangeable with most other 810’s.

Like most other tanks on the market the Mechman tank is top filled and uses push-to-fill. It’s firm enough that it’s not going to open up in your pocket but easy enough to open without too much effort — it’s a happy medium. There’s a silicone gasket that surrounds the fill port to prevent leaking as well.

The airflow on the Mechman consists of two wide slots that are fully adjustable. They can be opened or closed according to your preference but it’s still going to be a direct-to-lung draw no matter how you position it. As opposed to the top cap, I found the airflow a bit too difficult to turn. It’s very tight so I found myself unscrewing the tank from the mod when trying to adjust it. It did loosen up a bit over time but I would of preferred the airflow control ring to be a bit easier to adjust.

Included with the kit are two mesh coils of different resistances. There’s a 0.20ohm dual mesh coil rated for 50-80W as well as a 0.25ohm single mesh coil rated for 40-60W. I got surprisingly good flavor and clouds out of both of these but I’ll go over their performance in depth a little later.

Features & Functions


This mod fires quite a bit higher than most other mods on the market. In power mode you get up to 228W of output. It uses Rincoe’s in-house chip for regulation which comes with a bunch of safety features built-in. It’s got overheating protection, low voltage protection, short-circuit/overload protection, reverse battery protection as well as a 10 second cut off if you fire the mod for too long.

For firing modes you get Power mode, Bypass Mode, Temperature Control mode and TCR. This is pretty much all you need, but if you’re looking for variable voltage you’re not going to find it with this mod.

The UI displays your battery charge level, set mode, wattage, puff time, resistance and output voltage. It’s a bit of an old-school looking design but it works to provide the information that you need about your vape. This mod is also simple and straightforward to use because there is no menu.

Button Combinations

Switch Modes: Press the fire button three times and use the adjustment buttons.

Lock the Device: Hold the + adjustment button and firing button.

Change Wattage in TC Mode: Hold the – adjustment button and firing button, then use the adjustment buttons to change the wattage. Press fire to confirm.

Performance


I tested the Mechman mod using the included Mechman tank and both mesh coils. I also tested the mod using the Hellvape Hellbeast as well as with the Bonza V1.5 RDA. Performance wise, this kit is pretty good.

The Mechman mod is pretty impressive. I didn’t have a need, nor the coils, to push it past 150W so I didn’t get to test it at 228W. However, while it lacks a more advanced menu, it works great in power mode all the way up to 150W; it certainly felt like it was delivering the correct wattage. Additionally, the mod was really good at reading the resistance of my atomizers correctly.

On the temperature control side of things, the Mechman is like most mods: mediocre. I didn’t find that it was delivering the right temperature and instead it felt like it was way too cool of a vape when set at 450°F. I had to turn it up to around 520°F in order to get what felt like the correct vape of 450°F. I would steer clear of this mod if you’re planning on using it for temperature control.

Another thing to note about this mod is its Bypass mode. With the 0.23ohm coil that came included, Bypass mode fires at 183W! While most other regulated mods will limit the voltage, Rincoe have told me that this mod is unrestricted with its Bypass. This means that you get the full voltage output of both batteries on a full charge which is not very useful to be honest. The reason most other mods limit the wattage output in Bypass is so that you can actually vape at a reasonable level, not singe your lips off! Unless you like burning your coils, I wouldn’t use Bypass mode with this mod as it ends up outputting wattages/voltages that are way too high for your coils to handle.

The Mechman sub-ohm tank with the 0.25 single mesh coil was alright in terms of flavor. It wasn’t bad at all but it definitely isn’t the best coil that I’ve used. The flavor was good and the clouds were also decent. However, it didn’t bring out the full flavor in my ejuices and this was a bit disappointing. The 0.20ohm dual mesh coil on the other hand was much better. I was vaping it at from 75-85W and the flavor was very on-point and on-par with some of the better sub-ohm tanks that I’ve used. It actually exceeded my expectations for a kit-included tank. I really enjoyed using the dual mesh coil with this tank and it made the whole kit a quite enjoyable experience.

Using the Hellbeast sub-ohm tank with the Mechman mod was very good. It delivered an accurate power output and vaped really well. The same can be said about the Bonza V1.5. I used 0.2ohm fused claptons and it fired and vaped marvelously.

Lastly, I’m going to end this on another positive note. The battery efficiency of this mod is really, really good. The Rincoe chip seems to sip power. Even when vaping at higher wattages it still lasted me about two days on average before I had to recharge. Where I usually average a day or less with most other dual battery mods at the same wattages, I’m not sure what kind of magic is going on here. However, I’m not going to complain!

Verdict


Overall, the Mechman kit is a good pickup for wattage mode vapers. The form factor is really nice and comparatively lightweight. Plus, the ability to swap our the panels for your own custom designs is something I’ve never seen before. This added personalization is really cool and I definitely rate it. It’s an awesome looking mod, that’s for sure!

The included Mechman sub-ohm tank functions well with the dual mesh coil and provides good flavor. Wattage mode works great and the battery efficiency of the mod is also notably good. However, for temperature control mode vapers I would suggest another mod.

What are your thoughts on the Mechman mod/kit? Let me know in the comments. Thanks for reading!

Now It’s Available : Rincoe Mechman Kit.

Hot Sale Recommendation:
Vaporesso Aurora Play Zippo Pod Starter Kit
Justfog Compact 14 Starter Kit
Rincoe Mechman Mesh Kit
Voopoo Drag Nano Kit
Voopoo Drag Baby Kit

Onevape Lambo Pod Kit Review

The Onevape Lambo is a tiny Pod system aimed at those giving up smoking, or for the more advance vaper who wants to carry around a second device.

onevape lambo pod kit hand

The Lambo Series is reported to be a high end pod system e-cigarette.

So who are OneVape? To be honest I’d never heard of them until I did some digging around! OneVape are based in Los Angeles California USA and Shenzhen China, they have dual head quarters enabling them to design and manufacture their products.

They don’t have many products at the moment and those they do are pod systems, the Nano Series as well as the Lambo Series.

So what do we think of the Onevape Lambo Pod? Let’s find out with an up and close look…………………

This Kit was sent to us for the purpose of review. As always my thoughts and views are my own.

In The Box

    • 1 x Lambo Pod Device
    • 2 x 2 ml Lambo Pods
    • 2 x spare plugs
    • 1 x USB Charging Cable
    • 1 x User Manual

onevape lambo pod kit

Main Specs/Features

  • 360 mAh built-in battery
  • Inhale activation
  • Rechargeable via USB
  • LED indicator
  • 2 ml refillable pods
  • 1.6Ω built-in coils
  • 5 different colours available

Design and Build Quality

The Lambo Series Pod Kit comes packed in a card box with a paper over sleeve.onevape lambo pod kit box

The Lambo pod system consists of two parts the stainless steel body and a plastic refillable 2 ml pod.onevape lambo pod kit sep

As you can see I have the Dazzling version, other colours are available Gold, Black, SS and Dazzle.

The device has a 360 mAh in built battery that while smaller than some on the market does last quite well for a mouth to lung device. The body of the Lambo is made from SS and has a lanyard loop so it can be worn around the neck!onevape lambo pod kit cordBelow the lanyard loop you have a micro USB charge portonevape lambo pod kit cpThe shape of the Lambo reminds me of an off centre octagon and the complete kit is very light at 63g without liquid and measure a compact 2.7” in height, 1.8” in width and 0.6” in depth.onevape lambo pod kit thin!The device is fired by the user sucking on the mouth piece of the pod, this is called auto fire or pneumatic draw, no buttons or screens here.

The base of the device has all the normal and relevant information laser printed on it.onevape lambo pod kit infoOne side of the device you have Lambo laser printed in white and the other side you have a deep ‘ONE’ stamp which is also the operation light which will light up blue on activated.onevape lambo pod kit mainI would say that the Lambo is well constructed; it looks good it is a tiny device that is very comfortable in the hand.

Focus On www.ave40.com For More Vape Kits.

Lambo Pods

The kit comes with 2 plastic bottom fill pods! 1 pre installed and 1 in the box,onevape lambo pod kit pdThe coils in each pod is rated at 1.6Ω and holds 2 ml of e-liquid, it is recommended a high PG liquid is used in the pods; however I have been using a 70/30 liquid without any trouble. It will also work well with nicotine salt e-liquid.

Quick Start Guide

Before use make sure the Lambo mod is fully charged.

  • Remove the white silicone plug from the mouth pieceonevape lambo pod kit bung
  • Remove the black silicone plug from the fill portonevape lambo pod kit fill plucg
  • Remove the paper sticker covering the connection points on the Podonevape lambo pod kit blue
  • Fill the pod with e-liquidonevape lambo pod kit filling
  • Replace the black silicone plug into the fill port
  • Place the pod into the device
  • Leave the device alone for 10 minutes so the cotton can soak up liquid

Battery light

  • When fired the battery light will come on and highlight the word ‘One’ in blue
  • When the battery is depleted it will flash blue
  • When charging the device it will light up red
  • Fully charged the light will turn green.

How Does the Lambo Pod Kit Perform?

For this review I have filled the pod with 3 mg “Blueberry Waffle” from Vintage Vaping.onevape lambo pod kit juice

Wattage

I’m not very good at determining what wattage a pod system fires at LOL but according to the OneVape website the device fires at 7 to 12w, which produces a fair Mouth to Lung (MTL) vape with good flavour.

I am able to get a very restricted Direct to Lung (DTL vape) which in turn produces a good amount of vapour and fair flavour but this is designed to be used as an MTL device so I recommend it be used as such.onevape lambo pod kit 1st puff

Pods

In the instructional manual that comes with the kit they say it is recommend you change the pod after 5 refills, so far in the week and a half I have been testing the kit I have only filled it twice lol, I would say that the pods have a fairly good life with MTL style of vape.

The pods have a circulating convection air passage that resists reverse air intake and are sold separately at around £9 for 2 pods.onevape lambo pod kit full

Battery

The 360 mAh internal battery is designed so that from a full charge you will get 270 puffs, I overlooked this the first time I charged the unit and did not count the puffs LOL.

I will tell you that the Onevape Lambo did last an entire day with MTL before needing a charge, I used the device exclusively for that day 8am until 5pm, 8hrs on a single charge is very good, so I will say the battery is long lasting!onevape lambo pod kit hide

Final Review Verdict

I’m not normally stuck for words about a product but in the case of the OneVape Lambo series pod kit I am! I really cannot find much to complain about with this kit if anything really.

The kit is fairly cheap and functions well, it’s ideal as a first e-cigarette or even as a second/spare carry around mod for those users that have more experience.

The airflow is fine, maybe a little loose for my liking but as I said above I’m able to get a restricted DTL vape.

Would I buy the Onevape Lambo Series Pod Kit should I lose or destroy the one I have? Not for me personally, I wouldn’t miss it.

Focus On www.ave40.com For More Latest Vape News.

Now It’s Available :    Onevape Lambo Pod System Kit

Hot Sale Recommendation:

Smok Nord Pod System Kit

Vaporesso Aurora Play Zippo Pod Starter Kit

SMOK Mico Pod Kit

OUMIER WASP Nano RTA 

Voopoo X217 Box Mod

Justfog Compact 14 Starter Kit

Think Vape Finder 167W – “inglorious” hit

Today, without any time machine, I will move you to the “distant” 2016, and, more precisely, it was almost a new year. Just then this “worthy” copy was born, for some reason completely forgotten on our portal. This is a gross injustice to him, so we rather get to know each otheragain – Think Vape Finder 167W .
Think Vape Finder 167W -
By the way, here you looked at the photo now, but most likely you have already seen it before. Reminds Therion DNA75 Therion DNA75 isnot it … And the most interesting, the release of our hero and Lost Vape Therion 166 Lost Vape Therion 166 took place almost simultaneously … As one TV host said – Coincidence? I do not think.

Dimensions: 92 x 55 x 30mm
Weight: 171g
Case material: zinc alloy + leather
Power supply: 2 x 18650
Chipset: Evolv DNA 250
Output power: 1 – 167W
Voltage range: 0.5 – 9.3V Peak
current: 55A
Operating mode: POWER, TC (NI200, SS, TI), TCR
Temperature range: 200 – 600 ℉ / 100 ℃ – 315 ℃
Supported resistance: 0.08 – 3.0Ω
Protection: from low / high resistance, overheating, from incorrect polarity, short circuit, overcharge / overdischarge
Connector type: steel 510, Pin is gold-plated, spring-loaded
Screen / diagonal: yes, 0.91 ”
Micro-USB port / charging:there are
Update / Firmware: yes
Color: black, steel, blue, Copper
Think Vape Finder 167W - inglorious hit ...
Components
– the Finder 167W mod
– the USB cable
– user manual
– warranty card
– gift wrap
Think Vape Finder 167W - inglorious hit ...
I think at the moment there is no point in discussing the possibility of DNA board, everyone knows that she is worth her money. So we will discuss only the external individual characteristics of the box mod.

The design is now classic, the progenitor in the face of Therion DNA75 is easily recognized. Very good form factor, so loved by the public. But still, you know, I prefer this device. Somehow he looks easier, more pleasant to the eye, not so overloaded with geometric elements or something.
Think Vape Finder 167W -
There is also a genuine leather insert, as an element of “prestige”. The only thing that “strains” me here is the fire button, which is incomprehensible for which is decorated with a “mother-of-pearl” insert. As for the rest, I will stay with my own opinion, everything is “perfect” here.
Think Vape Finder 167W -
Atomic landing is excellent, except that the landing site is too marking.
Think Vape Finder 167W -
The side panel is also removable, movable, access to the batteries is excellent, and the ribbon is not forgotten.
Think Vape Finder 167W -
Think Vape Finder 167W -
And here the question arises – why the users like Therion 166 so much, and our hero did not feel the gravity of the laurel wreath. Is it all depends only on the marketing program? After all, the price is clearly lower for him …
Think Vape Finder 167W -
Think Vape Finder 167W -
Advantages / disadvantages
+ design
+ performance (chipset)
+ constructive
+ price

Focus On www.ave40.com For More Latest Vape News.

Now It’s Available :

Think Vape Finder 250C 300W TC Box Mod with Evolv DNA Chipest

 Hot Sale Recommendation:

Smok Nord Pod System Kit

Vaporesso Aurora Play Zippo Pod Starter Kit

SMOK Mico Pod Kit

OUMIER WASP Nano RTA 

Voopoo X217 Box Mod

Glass walls: Sinuous V80 Box Mod by Wismec

Wismec has released Sinuous V80 box mod. The compact device was given a bare board with a capacity of 80 watts and powered by a single battery with the ability to quickly charge up to 2A.

On January 3, Wismec introduced the Sinuous V80 device on the Facebook page  . The low box mod was clad in a translucent plastic case framed with metal. The corners smoothly smoothed, sharp edges were excluded. The landing area was calculated for 26 mm and supplemented with cruciform ducts. The front control panel included a rectangular fire button, a display, a couple of buttons for adjustment, and a USB port. A hinged lid with vents was attached to the bottom.

Power of the device is regulated in the range from 1 to 80 watts, it is also possible to work in bypass and thermal control modes. Power is supplied from a single 18650 battery. You can charge the battery in a relatively short time using the QC USB cable. Resistance ranges from 0.05 to 3.5 ohms.

The device can be purchased in conjunction with the Amor NSE tank, presented in the previous set.

The standard kit includes QC USB cable, parts and instructions.

Main characteristics:

  • Size – 81 by 34 by 27 mm
  • Weight – 59.8 mm
  • Meals – 1×18650
  • Charging current up to 2A
  • Maximum power – 80 watts
  • Resistance from 0.05 to 3.5 ohms

Focus On www.urvapin.com For More Latest Vape News.

Now It’s Available : Wismec Sinuous V80 Kit with Amor NSE Tank

Hot Sale Recommendation:

Smok Nord Pod System Kit

Vaporesso Aurora Play Zippo Pod Starter Kit

SMOK Mico Pod Kit

OUMIER WASP Nano RTA 

Voopoo X217 Box Mod

Joyetech UNIMAX 25 Review

Joyetech UNIMAX 25 Full Review

As part of Joyetech’s ongoing effort to maintain its status as one of the world’s premiere vaping companies, producing some of the best vape pens on the market, it is continually developing new products that push the technological and performance envelope. Its new Joyetech UNIMAX 25 offering is another step in that direction, offering a cutting-edge pen-style product that should have vaping enthusiasts cheering in their seats. That is if you can believe the hype that surrounds that product. In this Joyetech UNIMAX 25 starter kit review, we’ll examine the product to see if it can even begin to live up to our lofty expectations.

 

The Rundown

The UNIMAX 25 offers a streamlined appearance that makes it one of the sleeker, more portable devices I’ve seen in some time. Its outward appearance is elegant and fairly nondescript, but you can alter it with the provided stickers. There are various color themes from which to choose, and some of them have textures as well. It’s an interesting little feature that should appeal to anyone interested in customizing his or her device to match apparel, mood, or personal style.

The complete kit of the Joyetech UNIMAX 25

The device has that TFTA system that you’ve probably already heard about. It’s top-fill and top-airflow, and it’s one of the main selling points for those who want maximum control over their device for sub-ohm vaping. The top-focused design helps to guard against leaks, since any airflow adjustments are done well above the juice, reducing the chances for any leakage. And, of course, vapers tend to prefer the top-fill option, as is usually makes for a less messy filling process.

The starter kit comes with a 3000mAh battery that takes up about two-thirds of the cylinder. It’s designed to provide just the output you need for your vaping sessions. The device’s tank should come as a pleasant surprise for many – especially if they’re buying products made for the European market. While many companies have begun to focus on limiting product tank sizes to the 2-ml required to meet EU guidelines, this Joyetech product ignores that tiny capacity and opts for a much larger 5 ml tank. Good for them. The smaller tank limitations don’t really accomplish anything, anyway – other than placing more burdens on companies and causing annoyance for vapers.

Focus On www.urvapin.com For More Vape Start Kit.

Performance Capacity

The testing reveals that this device can achieve 40 watts of power when you’re using a 0.5-ohm coil. The company notes that you can achieve output between the 20 to 40-watt range. The battery cell can handle resistance ranging from 0.15 to 3.5 ohms, of course, but you should shoot for that 0.5-ohm level. That’s where the magic happens especially if you’re looking to vaping to quit smoking. From a power standpoint, this is not the most powerful device we’ve ever seen – but there’s power and then there’s useful power. The larger question is whether the UNIMAX 25 can deliver enough power to provide the vaping experience its users are seeking.

 

Dimension of the Joyetech UNIMAX 25

On that front, there are no worries. While we didn’t manage to generate any room-filling clouds of vapor, we did achieve nice, the thick vapor that was filled with our e-juice flavor. More importantly, those results were consistent throughout several vaping sessions, with no overheating, dry hits, or other uncomfortable effects. That’s the type of power we like to see.

It’s also important to note that the device is designed to be compatible with a variety of coils, and has the standard 24 mm tank design so many users are already familiar with. It’s also compatible with any standard 510 drip tip so that you can change out the Delrin drip tip if you find it to be less than useful.

Finally, let’s not fail to note this little gem: the device is designed for direct-to lung inhalation. That’s critical to remember since you do want to evaluate it in terms of its intended use to ensure that your comparisons are accurate. In our opinion, it’s one of the top e-cigarettes for lung hits we’ve seen.

Parameters of the UNIMAX 25

 

Putting it all Together

This device seems to have it all, especially when you consider that you can get the entire starter kit package for just under $40 online. So, is it worth it? Well, that depends on what you’re looking for. If you want a product that offers a safe and clean way to enjoy your vapor without the undue mess, then this could be the device you need. If you’re looking for another high-end, fully-customizable device that you can rebuild to your heart’s content, then look elsewhere. This device is clearly designed for vapers who want a high-capacity tank to provide them with hours of nonstop vaping pleasure.

Focus On www.urvapin.com For More Latest Vape News.

Now It’s Available :

Joyetech UNIMAX25 AIO starter kit

Hot Sale Recommendation:

Smok Nord Pod System Kit

Vaporesso Aurora Play Zippo Pod Starter Kit

SMOK Mico Pod Kit

OUMIER WASP Nano RTA 

Voopoo X217 Box Mod

Vandy Vape Kylin RTA V2 Review | Postless Deck Made Easy

Product intro

The Kylin RTA was one of Vandy Vape’s most popular tanks to date. Based on its success, they released the Kylin Mini, which was also a big hit. Today we are looking at the Kylin V2, the latest update in the Kylin line-up. It features a few updates to the original, while maintaining a familiar design and aesthetic.

The tank features the same post-less “halfpipe-style” deck from the V1, but with an updated airflow design. It also utilizes a new top-filling system that snaps open to reveal a big fill port. The Kylin series is best known for its great flavor, so let’s find out whether or not this has been improved on the version 2.

Build quality and design

Vandy Vape Kylin V2 RTA

The Kylin V2 is 24 mm in diameter and holds 3 mL with the straight glass tube, or 5 mL with the 26 mm extension. It holds almost as much as the V1 with the extended glass, while maintaining a low-profile design. It also allows your coils to sit a little bit closer to your mouthpiece, which is another big plus.

Overall it feels well machined, the threading is very smooth. I didn’t have any issues taking the tank apart for cleaning and building. The Kylin V2 includes a Goon-style resin drip tip that’s compatible with my Half Moon drip tips, and has a similar look to it. It comes with a wider black mouthpiece and a 510 drip tip adapter.

The Kylin now has a sliding top-fill mechanism. It takes a bit of force to get it fully open, but it makes a nice snapping sound when you do. It doesn’t seem to shut with the same authority. Be sure to close it all the way, without leaving a lip on the edge. The tank has a small engraved dot on the top to indicate where it opens, but I found it very hard to locate even in good lighting, which was a bummer. On the Vandy Vape website, the final production model is pictured with a more visible arrow on top instead.

I like the matte black finish on the one that I received, and some of the other color options look nice too. I’m not in love with the overall aesthetics, but it has a gear-style textured design that reminds me of the old Twisted Messes RDA, which is cool. I can’t complain, it has a simplistic design that I do appreciate.

Build deck

Vandy Vape Kylin V2 RTA

Vandy Vape is sticking with a cambered-style deck. It has a U-shape, similar to a skateboard ramp. The design is postless, and accommodates both single and dual coil configurations nicely, with the coils sitting right in the center. The deck has four strong hex screws on each corner of the deck, just like the new Phobia V2 RDA. They both have a similar postless build deck that is good for trapping your leads.

The wicking slots appear to be rather slim. I’m guessing the wicking for this device is going to be very particular in order to get the right performance. The tank comes with some beefy fused claptons, so I’ll need just the right amount of cotton to go through them, tapering them down into the wick ports.

Focus On www.urvapin.com For Best Vape Tanks.

Coil installation

Vandy Vape Kylin V2 RTA

The coil cutting tool is to key for quick coil installation. It actually cut a few minutes off the coil-building process. The tool has a sticker on it to indicate the perfect length for this particular deck. I took the coils included with the tank, and snipped them accordingly. It’s a brilliant idea that Vandy Vape now includes this tool with all their devices that have postless decks, to make them more accessible. Then I just placed the coils in the slots and tightened up the hex screws while gently holding them in place. The grub screws did a great job trapping the wire, and the overall process was easy and quick.

Wicking the device did take some trial and error. You’ll want to use a good amount of cotton to fill up the coils, but you have to cut them at an angle before tucking them into the slots. I did experience some dry hits when I first started using the Kylin V2, but after some practice, it was wicking without any problems. Fluffing your cotton helps, but more importantly, just don’t overstuff those wicking ports. Also, if you don’t use enough cotton, you’ll get some spitback and possible leakage from the bottom airflow slots.

Performance

Vandy Vape Kylin V2 RTA

Initially I was having some issues with dry hits, and I was not happy. It turns out it was the e-juice I was using. It had a ton of sweetener in it, and wasn’t doing very well at 60 watts with 0.15 ohm dual coils. I had better luck at 50 watts, but I wasn’t really able to chain vape it with the airflow wide open. I decided to switch it out for one with less sweetener, and with a similar PG/VG ratio. It started wicking much better, and I was able to chain vape it at 60 watts, no problem — even with the airflow maxed out.

The tank seems to be running through e-juice incredibly fast using the stock coils. I can almost count on my fingers the amount of puffs I can take until it’s time to fill. The Kylin V2 doesn’t wick down to the last drop either, it starts to give you dry hits if you don’t fill it up in time, which comes faster than you think. Just keep an eye on it. Make sure to close the airflow holes when filling and never leave the top open, or it can start to leak from the bottom.

Once I got the wicking just right, the performance was on point. I am getting a very saturated vape from this tank — it’s juicy! The vapor is warm, condensed and flavorful, especially using a dual-coil setup. It still performed well in single coil mode, but puts out a lot more flavor in a dual coil configuration. The tank can accommodate coils with a 3.5 mm ID, I wouldn’t go much bigger despite its large chimney.

I played around a bit with the coil placement but it didn’t have a huge impact on the overall performance. I liked having the dual coils right the middle, above the airflow and as close as possible without touching. The clouds it produced were dense and thick, the kind that slowly drift to the floor. It chucks for sure. I would classify this as more of a flavor chasing tank, but it does great with clouds too.

Airflow

Vandy Vape Kylin V2 RTA

The airflow on the Kylin V2 is incredibly smooth. It provides enough airflow for clouds while maintaining very saturated flavor. It still has a bit of restrictiveness, even at its widest setting, which I like. The deck has a bevelled insert that directs the airflow up through the center of the deck, right beneath your coils. It looks like it’s made out of ceramic, but there is no official word from Vandy Vape on the material used.

I think the slight restriction is caused by the deck, because it has narrow airflow slots, instead of the four big holes on the original. This also contributes to the smoothness of the draw, which is noticeable. Closing off the airflow halfway gives you a smooth restrictive lung hit, with warm condensed flavor. The Kylin V2 puts out more than enough airflow for the mid to high wattage output range.

Pros / Cons

  • Saturated flavor
  • Easy to build
  • Easy top-fill
  • Smooth airflow
  • Nice resin drip tip
  • Single/dual coil compatible
  • Dense cloud production
  • Must close airflow when filling
  • Wicking requires precision

Verdict

With all things considered, the Kylin V2 is a solid RTA. It’s well constructed and comes with all the extra bells and whistles like a coil-cutting tool, a cool resin drip tip and some nice fused Claptons. I wouldn’t recommend it to a beginner vaper because of the wicking situation, but I would to the more experienced builders and flavor chasers. You might not nail it down right away, but when you do, it’s flavor for days!

If you already own the original Kylin RTA, this may just be the upgrade you’ve been waiting for. The V2 has a more modern look and comes with improved performance. It’s a nice overall value, especially considering the price. If you’re looking for a low-profile rebuildable tank with awesome flavor, and you have some experience with wicking RTAs, then you are going to appreciate this tank. What do you think about the Vandy Vape Kylin V2 RTA? Share your thoughts in the comment section below.

Now It’s Available :

VandyVape Kylin Mini RTA Tank

Hot Sale Recommendation:

Smok Nord Pod System Kit

ijoy shogun kit

ijoy shogun univ

ijoy shogun mod

smok stick v9

Coilart Mage Mech V2.0

Hotcig G100 – style and quality

The company Hotcig is again on the front pages of our portal. Most recently, they presented an outstanding AIO set and now they rolled out a single can mod. It is noteworthy that the developers did not load this new product with “useless” non-service in order to cut down more on the release. But quite the contrary, they gave the user the right to independently choose the best option without overpayment for what he will not use. 

Hotcig G100 
Hotcig G100 - style and quality ...
Dimensions: 92 x 34 x 31mm 
Weight: unknown 
Case material: zinc alloy + plastic 
Food: 1 x 18650/1 x 20700/1 x 21700 
Chipset: HM chip waterproof 
Output power: 5 – 100W 
Operating mode:POWER, TC (NI200, SS, TI), BYPASS 
Temperature range: 200 – 600/100 – 315 ℃ 
Supported resistance: 0.1 – 3.0Ω 
Protection: from low / high resistance, from overheating, from short circuit, from incorrect polarity, overcharge / overdischarge 
Connector type: steel 510, pin gold-plated, spring-loaded 
Screen / diagonal: yes, 0.9 ” 
Update / firmware: probably 
Micro-USB port / charge: yes, charging current is unknown 
Color: see photo below 
Hotcig G100 - style and quality ...
Package
contents – G100 mod 
– battery adapter size 18650 
– USB cable 
– user manual
– warranty card 

Exterior of our hero is quite decent, even handsome and stylish. On this, not every atom will look. There is absolutely no décor at all – on the contrary, clear and strict, but rounded lines. And the form factor is quite comfortable and acceptable. In short, the developers worked – you can not say otherwise. 
Hotcig G100 - style and quality ...
The color scheme is not very rich, only three colors. Well, thanks for that. 
Hotcig G100 - style and quality ...
The steel landing area, apparently, is not worth worrying about especially for landing large atoms. 
Hotcig G100 - style and quality ...
The control panel is minimalistic, supports the overall concept of decoration. The buttons are small, they seem to be hidden in the case, without attracting too much attention. The display is monochrome small, right at the base, but on the side panel there is a connector for charging the battery and probably the firmware of the device.
Hotcig G100 - style and quality ...
Compartment for the battery did not show us, most likely it is hidden behind a removable panel on the back of the device. It is noteworthy that the developers instilled in the novelty omnivorous in terms of used batteries, and did not forget to attach the adapter for smaller sizes. 
Hotcig G100 - style and quality ...
Performance is decent for this segment. Inside it already familiar, but modernized, waterproof control chipset. 
Hotcig G100 - style and quality ...

Now It’s Available :

Hotcig G100 100W TC Box Mod

Hot Sale Recommendation:

Smok Nord Pod System Kit

ijoy shogun kit

ijoy shogun univ

ijoy shogun mod

smok stick v9

Coilart Mage Mech V2.0